The method of measuring the physical and mechanical parameters of cutting during the turning process

The article gives a brief review preceding the following research of the method of measuring the cutting parameters during the turning process. We introduce a classification of the main temperature measuring instruments and cutting force components. The commonly used methods for measuring the cutting force components and temperature are discussed. The work gives detailed analysis of the measurement methods for physical and mechanical parameters of the cutting process and finds out major disadvantages of these methods. We have developed a general layout of the measuring stand and a control software program of registering physical and mechanical parameters of cutting in the graphical programming environment LabVIEW 2011. The article describes the components of the measuring stand flowchart used for measuring the physical cutting parameters during the turning process. We point out the capabilities and advantages of this installation when applying the graphical programming environment LabVIEW 2011.

References

[1] Bez”yazychnyy V.F., Kordyukov A.V., Timofeev M.V., Fomenko R.N. Development of dynamometer system for measuring cutting forces when turning. Izvestiya MGTU MAMI, 2014, vol. 2, no. 1 (19), pp. 171–176.

[2] Kozlov V.N. Rezanie materialov i rezhushchiy instrument [Cutting of materials and cutting tools]. Tomsk, TPU publ., 2014, 131 p.

[3] Vinogradov D.V., Dreval’ A.E., Vasil’yev S.G. System for assessment of material wearing capacity and cutting forces while turning. Inzhenernyy vestnik [Engineering Bulletin], 2014, no. 9. Available at: http://engsi.ru/doc/727928.html (accessed 12 December 2017).

[4] Rukovodstvo k universal’nomu dinamometru UDM konstruktsii VNII [Guide to universal UDM dynamometer of VNII construction]. Moscow, VNII publ., 1979, 22 p.

[5] Mal’kova L.D. et al. Fizicheskie osnovy mekhanicheskoy i fiziko-tekhnicheskoy obrabotki materialov [Physical basis of mechanical and physical-technical treatment of materials]. Moscow, Bauman Press, 2016, 88 p.

[6] Mal’kov O.V., Golovko I.M. Eksperimental’noe opredelenie modeli sily pri rez’bofrezerovanii [Experimental definition of force model in process of thread milling]. Sbornik trudov Mezhdunarodnoy molodezhnoy konferentsii “Innovatsii v mashinostroenii” [Proc. Int. Youth Conf. “Innovations in mechanical engineering”]. Tomsk, TPU publ., 2012, pp. 73–77.

[7] Mal’kova L.D. Estimating power consumption for flat surface machining employing various milling techniques. Inzhenernyy zhurnal: nauka i innovatsii [Engineering Journal: Science and Innovation], 2016, no. 12 (60). Available at: http://engjournal.ru/catalog/mesc/tempp/1559.html (accessed 14 December 2017).

[8] Kosenko A.I. Sbornik metodicheskikh ukazaniy po predmetam: Rezanie materialov i Rezanie materialov i rezhushchiy instrument [Methodology instructions on courses: Materials cutting and Materials cutting and non-destructive tools]. Novogorod, Izd-vo NovGU, 2006, 140 p.

[9] Dreval’A.E., Vasil’yev p.G., Vinogradov D.V., Mal’kov O.V. Measuring diagnostic stand for experimental researches in technology machining. Nauka i obrazovanie: nauchnoe izdanie [Science and Education: Scientific Publication], 2014, no. 12, pp. 22–58. Available at: http://technomag.bmstu.ru/doc/749286.html (accessed 12 December 2017).

[10] Shulyak Ya.I., Vasil’yev S.G. A modernized UDM-600 dynamometer-based setup for the cutting force measurement. Mashiny i ustanovki: proektirovanie, razrabotka i ekspluatatsiya [Machines and Plants: Design and Exploiting], 2016, no. 1. Available at: http://maplants.elpub.ru/jour/article/view/33 (accessed 14 December 2017).