Creating sections in Autodesk Inventor system

Authors: Pavlova I.I., Taklenok E.A.
Published in issue: #10(39)/2019
DOI: 10.18698/2541-8009-2019-10-542
Category: Informatics, Computer Engineering and Control | Chapter: Automation, Control of Technological Processes, and Industrial Control
Keywords: engineering graphics, computer graphics, Autodesk Inventor, section, section designation, ESKD, drawing, model, electronic document
Published: 28.10.2019

The article shows the work in the graphical environment of the computer-aided design system Autodesk Inventor and describes the commands for creating a part drawing and creating sections. Various methods for making a section of a part are considered for the case when it is necessary to designate a section. Particular attention is paid to the design of the part image combining half of the general view with half of the section using the "Crop" command in Autodesk Inventor’s computer-aided design system. The advantages and disadvantages of various methods for constructing part sections with the designation for the Autodesk Inventor graphic system in accordance with the requirements of the Unified Design Documentation System (ESKD) are shown.

References

[1] Khusnetdinov T.R., Polubinskaya L.G., Maksutova R.A., et al. Using 3D simulation systems in teaching students disciplines of RK-1 “Engineering graphics” academic department. Inzhenernyy vestnik [Engineering Bulletin], 2016, no. 11. URL: http://engsi.ru/doc/851407.html (in Russ.).

[2] Zhirnykh B.G, Mineev A.B., Polubinskaya L.G., et al. Information technologies in geometrical-graphical training students of “Computer systems of production automation” (RK9). “Komp’yuternye sistemy avtomatizatsii proizvodstva” (RK9). Aktual’nye problemy gumanitarnykh i estestvennykh nauk, 2017, no. 2-2, pp. 64–66 (in Russ.).

[3] Khusnetdinov T.R., Polubinskaya L.G., Pavlov A.Yu., et al. Transferring of drawings into electronic form. Nauchnaya mysl’, 2017, no. 4, pp. 35–39 (in Russ.).

[4] Polubinskaya L.G., Khusnetdinov T.R., Uvaysova A.S. The influence of 3D modeling on the course of engineering graphics. Innovatsionnoe razvitie, 2018, no. 5(22), pp. 53–54 (in Russ.).

[5] Polubinskaya L.G., Senchenkova L.S., Fedorenko V.I., et al. Vypolnenie chertezhey detaley v kurse inzhenernoy grafiki [Parts drawing in engineering graphics course]. Moscow, Bauman MSTU Publ., 2014 (in Russ.).

[6] GOST 2.305-2008. Edinaya sistema konstruktorskoy dokumentatsii (ESKD). Izobrazheniya – vidy, razrezy, secheniya [State standard 2.305-2008. Unified system for design documentation. Images - appearance, sections, profiles]. Moscow, Standartinform Publ., 2009 (in Russ.).

[7] Fedorenkov A.P., Polubinskaya L.G. Autodesk Inventor. Shag za shagom [Autodesk Inventor. Step by step]. Moscow, Eksmo Publ., 2008 (in Russ.).

[8] GOST 2.307-2011. Edinaya sistema konstruktorskoy dokumentatsii (ESKD). Nanesenie razmerov i predel’nykh otkloneniy (s Popravkami) [State standard 2.307-2011. Unified system of design documentation. Drawing of dimensions and limit deviations]. Moscow, Standartinform Publ., 2011 (in Russ.).

[9] GOST 2.104-2006. Edinaya sistema konstruktorskoy dokumentatsii (ESKD). Osnovnye nadpisi [State standard 2.104-2006. Unified system for design documentation. Basic inscriptions]. Moscow, Standartinform Publ., 2006 (in Russ.).

[10] Goryachkina A.Yu., Koryagina O.M., Khusnetdinov T.R. Methodological aspects of developing evaluation tools for online courses in graphic subjects. Glavnyy mekhanik [Chief Mechanical Engineer], 2019, no. 3, pp. 46–50 (in Russ.).