Influence of technological processing techniques on load-carrying capacity of gear wheels

Authors: Ternichenko V.A., Konovalov D.P., Pereverten E.A.
Published in issue: #12(17)/2017
DOI: 10.18698/2541-8009-2017-12-218
Category: Mechanical Engineering and Machine Science | Chapter: Machine Science, Drive Systems, and Machine Components
Keywords: load-carrying capacity of gear wheels, technological processing techniques, surface roughness, surface layer microrelief
Published: 29.11.2017

We consider the main processing techniques of gear wheels of different modules and note the advantages and disadvantages of every method. The special attention is given to finishing operations (gear grinding, honing, lapping, burnishing). Due to these the surface layer microrelief is formed. Findings of the research show that the choice between the mechanical finishing or control processing operations depends on the purpose and precision of gear wheels.

References

[1] Eliseev Yu.S., Krymov V.V., Nezhurin I.P. Proizvodstvo zubchatykh koles gazoturbinnykh dvigateley [Production of gears for gas-turbine engines]. Moscow, Vysshaya shkola publ., 2001, 492 p.

[2] Fomina L.P., Krymov V.V. Improvement hardening technology for aircraft engine gears. Dvigatel’ [Engine], 2016, no. 2, pp. 6–8.

[3] Pavlikov P.Ya., Shatalov V.K., Yakovleva A.P. Kombinirovannaya uprochnyayushchaya obrabotka krupnogabaritnykh zubchatykh koles [Combined strengthening treatment of large gears]. Energotekhnologicheskie protsessy. Problemy i perspektivy. Sb. st. [Energy-technical processes. Problems and prospects. Collection of articles]. Moscow, Bauman Press, 2000, pp. 141–151.

[4] Isaev A.I., Kotkina M.G. Surface roughness of gears. Vestnik mashinostroeniya, 1967, no. 12, pp. 64–66.

[5] Feofilov N.D., Vorob’yev I.A., Yanov E.S. Research on part surface layer under hobbing by interlocking hob cutters. Izvestiya TulGu. Tekhnicheskie nauki, 2015, no. 10, pp. 92–99.

[6] Yakovleva A.P. Strengthening of coarse pitch gears. Aviatsionnaya promyshlennost’ [Aviation Industry], 2014, no. 2, pp. 31–33.

[7] Vitenberg Yu.R., Petrusevich A.I. Effect of treatment on sliding strength of lubricated rough surfaces with combined rolling and sliding friction. Vestnik mashinostroeniya, 1976, no. 6, pp. 12–17.

[8] Ponomarev V.P., Batov A.S., Zakharov A.V., Murzin V.A., Tolmachevskiy N.N. Konstruktorsko-tekhnologicheskoe obespechenie kachestva detaley mashin [Design-engineering quality assurance of machine parts]. Moscow, Mashinostroenie publ., 1984, 184 p.

[9] Yakovleva A.P., Savel’yeva L.V., Naumov V.A., Sharapov S.N., Bessudnov L.I. Causes of gear wheels damage. Glavnyy mekhanik [Chief mechanical engineer], 2017, no. 1, pp. 43–48.

[10] Genkin M.D., Ryzhov M.A., Ryzhov N.M. Povyshenie nadezhnosti tyazhelonagruzhennykh zubchatykh peredach [Increasing of power gears reliability]. Moscow, Mashinostroenie publ., 1981, 232 p.

[11] Zabrovski T.U. Povyshenie effektivnosti protsessa zuboshlifovaniya na osnove upravleniya tochnost’yu i kachestvom poverkhnostnogo sloya zub’yev [Increasing of gear-tooth grinding process effectiveness based on control of tooth surface layer accuracy and quality]. Moscow, MSTU Stankin publ., Yanus-K publ., 2006, 186 p.