Main Catalog Mechanical Engineering and Machine Science Technology and Equipment of Mechanical and Physical Processing

Review of methods for the theoretical determination of cutting power of the strength of foreign scientific school

Authors: Popov N.A.
Published in issue: #1(30)/2019
DOI: 10.18698/2541-8009-2019-1-432
Category: Mechanical Engineering and Machine Science \| Chapter: Technology and Equipment of Mechanical and Physical Processing
Keywords: metal cutting, cutting power, external turning, cutter, machining, chip formation, зона резания, cutting area, shear angle, tool wear
Published: 04.02.2019

The paper is concerned with a brief review and analysis of methods for the teorethical determination of cutting force developed in foreign scientific schools. The authors proposed the schemes for calculating the components of the cutting foirce, presented in the original publications, analytical models and fundamental approaches of the authors to the problem under consideration. In this paper the authors show analogies with domestic developments. The analysis based on the author’s translation of English publications by specialist such as F. Klocke, M.E. Merchant, J.P. Davim and V.P. Astakhov, that representing fundamentally different approaches to determining the dynamic and energy characteristics of the cutting process.

References

[1] Vinogradov D.V., Dreval’ A.E., Vasil’yev S.G. Complex for assessment of material wear-resistance and cutting forces at grinding. Inzhenernyy vestnik [Engineering Bulletin], 2014, no. 9 URL: http://engbul.bmstu.ru/doc/727928.html (in Russ.).

[2] Dreval’ A.E., Mal’kova L.D. Complex impact of mechanical treatment parameters on magnitude of cutting force components. Izvestiya vysshikh uchebnykh zavedeniy. Mashinostroenie [Proceedings of Higher Educational Institutions. Маchine Building], 2007, no. 8, pp. 53–61 (in Russ.).

[3] Dreval’ A.E., Vinogradov D.V., Mal’kov O.V. Defining a minimum end mill diameter. Nauka i obrazovanie: nauchnoe izdanie [Science and Education: Scientific Publication], 2015, no. 11 URL: http://engineering-science.ru/doc/827318.html (in Russ.).

[4] Dreval’ A.E., Vasil’yev S.G., Vinogradov D.V., et al. Measuring diagnostic stand for experimental researches in technology machining. Nauka i obrazovanie: nauchnoe izdanie [Science and Education: Scientific Publication], 2014, no. 12 URL: http://engineering-science.ru/doc/749286.html (in Russ.).

[5] Mal’kov O.V., Golovko I.M. [Experimental definition of force model at thread grinding]. Sb. tr. Mezhd. molodezh. konf. [Proc. Int. Youth Conf.]. Tomsk, TPU Publ., 2012, pp. 73–77 (in Russ.).

[6] Mal’kov O.V., Karel’skiy A.S. Modelling the cut layer when thread milling. Izvestiya vysshikh uchebnykh zavedeniy. Mashinostroenie [Proceedings of Higher Educational Institutions. Маchine Building], no. 9, pp. 54–64 DOI: 10.18698/0536-1044-2017-9-54-64 URL: http://izvuzmash.ru/catalog/tpmachines/hidden/1463.html (in Russ.).

[7] Mal’kova L.D. Power saving at engineering of turning technological process. Izvestiya vysshikh uchebnykh zavedeniy. Mashinostroenie [Proceedings of Higher Educational Institutions. Маchine Building], 2012, spec. iss., pp. 43–49. (in Russ.)

[8] Mal’kova L.D., Chikhareva M.A. A study of lathing characteristics on the basis of obtaining and analyzing multidimensional polynomial dependences. Nauka i obrazovanie: nauchnoe izdanie [Science and Education: Scientific Publication], 2013, no. 8 URL: http://engineering-science.ru/doc/589299.html (in Russ.).

[9] Mal’kova L.D. Analiz primeneniya drobnykh faktornykh planov v tekhnologicheskikh issledovaniyakh na primere mekhanicheskoy obrabotki. Nauka i obrazovanie: nauchnoe izdanie [Science and Education: Scientific Publication], 2016, no. 10 URL: http://engineering-science.ru/doc/847711.html (in Russ.).

[10] Mal’kova L.D. Estimating power consumption for flat surface machining employing various milling techniques. Inzhenernyy zhurnal: nauka i innovatsii [Engineering Journal: Science and Innovation], 2016, no. 12(60). DOI: 10.18698/2308-6033-2016-12-1559 URL: http://engjournal.ru/catalog/mesc/tempp/1559.html (in Russ.).

[11] Melkeris T.V., Vinogradov D.V. Determining a cutting force for curved section of cutting layer. Inzhenernyy zhurnal: nauka i innovatsii [Engineering Journal: Science and Innovation], 2014, no. 12 URL: http://engineering-science.ru/doc/745856.html (in Russ.).

[12] Shulyak Ya.I., Vasil’yev S.G. A modernized UDM-600 dynamometer-based setup for the cutting force measurement. Mashiny i ustanovki: proektirovanie, razrabotka i ekspluatatsiya [Machines and Plants: Design and Exploiting], 2016, no. 1, pp. 1–12 (in Russ.).

[13] Merchant M.E. Mechanics of the metal cutting process. I. Orthogonal cutting and a type 2 chip. Jour. Appl. Phys., 1945, vol. 16, no. 2, pp. 267–275.

[14] Merchant M.E., Ernst H. Chip formation, friction and high quality machined surfaces, surface treatment of metals. Surface treatment of metals. Vol 29. ASM, 1941, pp. 299–378.

[15] Merchant M.E. Basic mechanics of metal cutting process. J. Appl. Mech., 1944, vol. 66, pp. 168–175.

[16] Zorev N.N. Voprosy mekhaniki protsessa rezaniya metallov [Issues of metal cutting process mechanics]. Moscow, Mashgiz Publ., 1956 (in Russ.).

[17] Zorev N.N. Raschet proektsiy sily rezaniya [Calculation of cutting forces projections]. Moscow, Mashgiz Publ., 1958 (in Russ.).

[18] Klocke F. Manufacturing processes 1. Cutting. Springer, 2011.

[19] Klocke F. Manufacturing processes 2. Grinding, honing, lapping. Springer, 2009.

[20] Klocke F. Modeling and planning of manufacturing processes. Springer, 2007.

[21] Davim J.P. Modern manufacturing engineering. Springer, 2015.

[22] Davim J.P. Machining. Fundamentals and recent advances. Springer, 2008.

[23] Astakhov V.P. Tribology of cutting tools. Elsevier Science, 2013.

[24] Astakhov V.P. Geometry of single-point turning tools and drills: fundamentals and practical applications. Springer, 2010.