Design and engineering analysis of overhead crane construction by means of apm winmachine
| Authors: Kurov A.V. | Published: 29.11.2017 |
| Published in issue: #12(17)/2017 | |
| DOI: DOI: 10.18698/2541-8009-2017-12-208 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Machines, Units and Processes | |
| Keywords: computer simulation, overhead crane, design optimization, static calculation, dynamic analysis, engineering analysis, WinMachine, structure 3d | |
Analysis of influence of wheel mover structural characteristics on support-coupling flotation ability of vehicle
| Authors: Maksimov R.O. | Published: 29.11.2017 |
| Published in issue: #12(17)/2017 | |
| DOI: DOI: 10.18698/2541-8009-2017-12-211 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Machine Science, Drive Systems, and Machine Components | |
| Keywords: wheel mover, vehicle, analysis, toroid tire of adjustable pressure, high flotation tire, arch tire, pneumocytes, supporting surface, flotation ability | |
Influence of technological processing techniques on load-carrying capacity of gear wheels
| Authors: Ternichenko V.A., Konovalov D.P., Pereverten E.A. | Published: 29.11.2017 |
| Published in issue: #12(17)/2017 | |
| DOI: DOI: 10.18698/2541-8009-2017-12-218 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Machine Science, Drive Systems, and Machine Components | |
| Keywords: load-carrying capacity of gear wheels, technological processing techniques, surface roughness, surface layer microrelief | |
Liquefied petroleum gas as motor fuel ignited from fuse doze of diesel fuel
| Authors: Uyutov S.Yu. | Published: 29.11.2017 |
| Published in issue: #12(17)/2017 | |
| DOI: DOI: 10.18698/2541-8009-2017-12-219 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Forming Technologies and Equipment | |
| Keywords: gas motor fuel, liquefied natural gas, compressed natural gas, liquefied petroleum gas, fuel injection pump, diesel fuel | |
Model of a robot-tester for evaluating the quality of LED crystals
| Authors: Dmitriev O.I. | Published: 06.12.2017 |
| Published in issue: #12(17)/2017 | |
| DOI: DOI: 10.18698/2541-8009-2017-12-221 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Robots, Mechatronics, and Robotic Systems | |
| Keywords: automated process, robot-tester, elements of machine vision, light-emitting diode, 3D printer | |
Computing and simulating residual stresses in an R65 rail
| Authors: Khramova D.A., Egorova D.A., Zhilin Ya.D. | Published: 20.12.2017 |
| Published in issue: #1(18)/2018 | |
| DOI: DOI: 10.18698/2541-8009-2018-1-231 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Inspection and Diagnostics in Mechanical Engineering | |
| Keywords: ANSYS software, analytical computation, residual stresses, rails, rail steel | |
On the question of harmonic friction drive design
| Authors: Dementev M.R. | Published: 09.01.2018 |
| Published in issue: #1(18)/2018 | |
| DOI: DOI: 10.18698/2541-8009-2018-1-234 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Machine Science, Drive Systems, and Machine Components | |
| Keywords: harmonic friction drive, rotational motion | |
Load distribution between threads of a bolted joint depending on the nut type and thread lead
| Authors: Koroleva O.B. | Published: 09.01.2018 |
| Published in issue: #1(18)/2018 | |
| DOI: DOI: 10.18698/2541-8009-2018-1-235 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Machine Science, Drive Systems, and Machine Components | |
| Keywords: bolt, nut, threaded surface, convergence, contact compliance | |
Plotting the "resource — energy conversion efficiency" compromise curve family for a centrifugal PUMP
| Authors: Protopopov A.A., Isaev N.Yu. | Published: 09.01.2018 |
| Published in issue: #1(18)/2018 | |
| DOI: DOI: 10.18698/2541-8009-2018-1-237 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Machines, Units and Processes | |
| Keywords: pump, blade, rotor, mathematical model, hydraulic head | |
Technological characteristics of turning the chilled steel face and machine tools used for this purpose
| Authors: Aleksandrov Ya.V. | Published: 17.01.2018 |
| Published in issue: #2(19)/2018 | |
| DOI: DOI: 10.18698/2541-8009-2018-2-241 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment of Mechanical and Physical Processing | |
| Keywords: turning the chilled steel face, spindle mount on hydrostatic bearings, precision machine tool, sliding supports figures, hydrostatic guideways, vibration damping | |