Underlying rationale for the necessary protection level of medium weight category robotic vehicles
| Authors: Lakutin N.A., Tereshin S.S. | Published: 27.02.2018 |
| Published in issue: #2(19)/2018 | |
| DOI: DOI: 10.18698/2541-8009-2018-2-274 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Robots, Mechatronics, and Robotic Systems | |
| Keywords: unmanned ground vehicles, robotic systems, combat missions of the unmanned ground vehicles, destruction means, self-protection, penetrative capability, combatant branch | |
A methodology for calculating the cutting tap flute volume
| Authors: Grishin N.O. | Published: 06.04.2018 |
| Published in issue: #4(21)/2018 | |
| DOI: DOI: 10.18698/2541-8009-2018-4-285 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment of Mechanical and Physical Processing | |
| Keywords: flute, flute volume, analytical calculation, designing the tool, cutting action, cutting tool, cutting tap, thread profile | |
Graphoanalytical method of defining the limiting ratio of drawing the workpieces from the tapered thickness blanks
| Authors: Levina A.V., Storozhilov V.A., Fonarev D.A. | Published: 06.04.2018 |
| Published in issue: #4(21)/2018 | |
| DOI: DOI: 10.18698/2541-8009-2018-4-288 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Forming Technologies and Equipment | |
| Keywords: drawing, tapered thickness workpiece, logarithmic thickness distribution, limiting drawing ratio, radial stresses, the thickness of the disk-shaped blank edge, flange shift, matrix drawbead | |
Energy consumption when processing the steel workpieces with fast-cutting drills made from different chemical compounds
| Authors: Kupriyanova A.S. | Published: 10.04.2018 |
| Published in issue: #4(21)/2018 | |
| DOI: DOI: 10.18698/2541-8009-2018-4-291 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment of Mechanical and Physical Processing | |
| Keywords: energy consumption, wear, cutting tool, high-speed steel, cutting velocity, drill, power, drilling torque | |
Locating the workpiece in the vise to perform the technological impact
| Authors: Zinova V.V. | Published: 27.04.2018 |
| Published in issue: #5(22)/2018 | |
| DOI: DOI: 10.18698/2541-8009-2018-5-302 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment of Mechanical and Physical Processing | |
| Keywords: machine vise, inaccuracy of clamping, imprecision of the surfaces arrangement, spacing, workpiece inaccuracies, prismatic workpiece, deviation from perpendicularity, setting base | |
Development and investigation of the submersible vertical motion control system. trim difference loop synthesis
| Authors: Gostilovich S.O., Gostilovich A.O. | Published: 07.05.2018 |
| Published in issue: #5(22)/2018 | |
| DOI: DOI: 10.18698/2541-8009-2018-5-305 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Robots, Mechatronics, and Robotic Systems | |
| Keywords: submersible, mathematical model, trim difference, vertical motion, linearized model, feedback, proportional plus reset controller, adaptive system, transfer-function, the worst case of steadiness | |
Obtaining the thin diamond-like films by means of the pulsed laser deposition method and examining their properties
| Authors: Krivosheev A.V., Ponomarenko S.L. | Published: 05.06.2018 |
| Published in issue: #6(23)/2018 | |
| DOI: DOI: 10.18698/2541-8009-2018-6-324 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment of Mechanical and Physical Processing | |
| Keywords: diamond-like films, thin films, pulsed laser deposition, vacuum deposition, laser ablation, excimer laser, ellipsometry, thickness of thin films | |
Special techniques of hydroabrasive underwater cutting
| Authors: Bondarev I.S., Petrov A.A. | Published: 13.06.2018 |
| Published in issue: #6(23)/2018 | |
| DOI: DOI: 10.18698/2541-8009-2018-6-325 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment of Mechanical and Physical Processing | |
| Keywords: jet-forming nozzle, hydroabrasive jet, cavitation, cutting speed, mathematical simulation | |
Engineering approach to the computation of the focusing system of fiber-optics laser
| Authors: Vagin D.V., Simonov A.P. | Published: 13.06.2018 |
| Published in issue: #6(23)/2018 | |
| DOI: DOI: 10.18698/2541-8009-2018-6-327 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Technology and Equipment of Mechanical and Physical Processing | |
| Keywords: fiber-optics laser, laser optical system, laser beam distortion, quality of laser emission, optimal focal distance, laser emission beam diameter | |
Opal films and inverse structures formation by means of vacuum methods
| Authors: Galaganova E.N. | Published: 13.06.2018 |
| Published in issue: #6(23)/2018 | |
| DOI: DOI: 10.18698/2541-8009-2018-6-328 | |
| Category: Mechanical Engineering and Machine Science | Chapter: Forming Technologies and Equipment | |
| Keywords: opal, photonic crystals, thin-film coatings, vacuum methods, excluded region, microspheres, multilayer structure, absorber, alternative energy sources | |